Order Parts for the Dodge Power Wagon


Power Wagon

Ignition

Click here for other Part Sources

Spark Plugs for Flathead 6 - 230, 251 Engines 14mm, 3/8" reach, 13/16" hex
AC R45 (Civilian Trucks) GAP=.025 (6v), GAP=.035 (12v)
BOSCH WR9EC (Super Plug) GAP=.035
NGK# BR6S (traditional plug) GAP=.035
Autolite 295 (Military Vehicles Trucks) GAP=.025 or Check ebay

Spark Plugs Poly 318 V8 - 3/8" Reach; Gap .035 Torque Spark Plug = 30 foot pounds
Autolite 75 (discontinued)
Autolite 85
Autolite AP85
NGK 3332
NGK 7355
Champion 14 (RJ12YC)

Distributor Caps for Flathead 6 - 230, 251 Engines
6 Volts Standard Motor Products AL-96 (1940-41) Distributors-IGC
6 Volts Standard Motor Products AL-96 (1941-56) Distributors-IGC, IGS
6 Volts Standard Motor Products AL138 (1941-56) Distributors-IAY or Check ebay
12 Volts Standard Motor Products AL-130 (1955-?) Distributors-IAP, IAD, IAO
12 Volts Standard Motor Products AL-138 (1956-68) Distributors-IAY, IAT, IBR or Check ebay
24 Volts Autolite IAU-1055 (Currently available from MV Parts Dealers only)

Coils for Flathead 6 - 230, 251 Engines
6 Volts Standard Motor Products UC-14
12 Volts Standard Motor Products UC-12
24 Volts Autolite CT4002 -- www.sandstruck.com/landpart/military.htm and MV Parts Dealers only.
Standard Motor Products Ballast Resistor RU-11

Condensers for Flathead 6 - 230, 251 Engines
6 Volts Standard Motor Products AL-118 (1940-41) Distributors-IGC
6 Volts Standard Motor Products AL-118 (1941-44) Distributors-IAP, IGS
6 Volts Standard Motor Products AL-106 (1945-56) Distributors-IGC, IA0, IAD, IAY, IGC
12 Volts Standard Motor Products AL-118 (1956-68) or NAPA# AL869 for Distributors-IAP, IGS
24 Volts Standard Motor Products AL-118 for Distributors-IGC-4515A1, IAT, IBR

Ignition Wire Sets for Flathead 6 - 230, 251 Engines
6 Volts Standard Motor Products# 3600
12 Volts Standard Motor Products# 3600
OE Performance Plus; Universal Fit; Conductive/ Metallic Core w/ Bendable Terminals
Core Construction Suppression Core
Size 7mm
Insulation EPDM
Jacket Blended Silicone
Coil Wire 1 30"
24 Volts (Currently available from MV Parts Dealers only)

Points for Flathead 6 - 230, 251 Engines
6 Volts Standard Motor Products# AL-4652P GAP=.020 Distributors-IAT-4004,A, IAT-4011, IAT-4012,A, IAT-4101B,C
6 Volts Standard Motor Products# AL-4556P GAP=.020 Distributors-IA0, IAD, IAP, IAY, IAT, IGC, IGS
12 Volts Standard Motor Products# AL-4652P GAP=.020 Distributors-IAT, IBR
12 Volts Standard Motor Products# AL-4556P GAP=.020 Distributors-IAY
24 Volts Standard Motor Products# AL-4556P GAP=.020 Distributors-

Rotors for Flathead 6 - 230, 251 Engines
6 Volts Standard Motor Products AL-98 (1941-55) Distributors-IGC, IGS, IAP, IAD, IAO
6 Volts Standard Motor Products AL-151 (1941-55) Distributors-IAY
12 Volts Standard Motor Products AL-151 (1955-68) Distributors-IAY, IAT, IBR
24 Volts Standard Motor Products AL-150

Brakes


Master Cylinder
(1946-1956)(WDX, B1-3, C1-4) Raybestos MC544
(1957)(W300) Raybestos MC785
(1958-1966)(W300M, WM300) Raybestos MC22976
(1967-1968)(WM300) Raybestos MC36359
(M37/M37B1/M43) Raybestos MC544


Wheel Cylinders for WC 3/4 ton, WC 1.5 ton, 1946-1968 Power Wagon, M37/M37B1/M43
Front Left, Rear Left - Raybestos WC9375 or Check ebay
Front Left, Rear Left - Raybestos WC9376 or Check ebay

Note: Big Bore Back

Axle WDX-WM300


Axle flange to hub gasket FEL-PRO 4390 {#915565} DC Truck Parts
Front Brake Hose RAYBESTOS BH4900 {#454900} Professional Grade
Rear Brake Hose RAYBESTOS BH8116 Professional Grade
Oil Seal, Wheel Hub, Inner, Front and Rear Axle - TIMKEN 417485 National 417485 CC915499
Bearing, Wheen Hub, Inner Race - Timken 28622
Bearing, Wheen Hub, Inner Bearing - Timken 28682
Bearing, Wheen Hub, Outer Race - Timken 2924
Bearing, Wheen Hub, Outer Bearing - Timken 2984


Clutch


Contact Dave Cirillo, dc@jobrated.com or check Daves ebay store

CLUTCH and RELATED PARTS (230)
Clutch Cover Assembly (10"-10 Splines-1D) ----- Perfection Clutch# - CA1864, NAPA# 1647
Clutch Disk (10"-10 Splines-1D) ----- Perfection Clutch# - RCF319
Clutch Release Bearing Assembly --------------- Perfection Clutch# - N1313 (Bearing and Sleeve Assembly)
Clutch Release Bearing ------------------------ SKF# - N1087, Timken - 2065, NAPA 1087, NATIONAL 2065
Clutch Pilot Bearing (Crankshaft) ------------- SKF# - B286, BCA# - PB286HD
Flywheel Ring Gear, 146 Tooth, CC1138903, Pioneer FRG146XF (6V & 12V), NAPA 6003010

CLUTCH and RELATED PARTS (251)

Clutch Cover Assembly (11"-10 Splines-1D) ----- Perfection Clutch# - CA1447
Clutch Cover Assembly (11"-10 Splines-1-3/8D) - Perfection Clutch# - CA1433
Clutch Disk (11"-10 Splines-1D) ----- Perfection Clutch# - RCF497
Clutch Disk (11"-10 Splines-1-3/8D) - Perfection Clutch# - RCF441
Clutch Release Bearing Assembly --------------- NATIONAL DC2065C SKF# - N1459
Clutch Release Bearing ------------------------ SKF# - N1087, Timken - 2065, NAPA 1087, NATIONAL 2065
Clutch Pilot Bearing (Crankshaft) ------------- SKF# - B286, BCA# - PB286HD

CLUTCH and RELATED PARTS (315)
Clutch Cover Assembly (11"-10 Splines-1D) ----- Perfection Clutch# - CA1433
Clutch Disk (11"-10 Splines-1D) ----- Perfection Clutch# - RCF497
Clutch Release Bearing Assembly --------------- NAPA# - N1313
Clutch Release Bearing ------------------------ SKF# - N1087, Timken - 2065, NAPA 1087, NATIONAL 2065
Clutch Pilot Bearing (Crankshaft) ------------- SKF# - B286, BCA# - PB286HD

1 inch Clutch Alignment Tool - Autozone #20, Pioneer# TAT-5349

Engine

Engine Front Support Insulator Assembly - Motor Mount
L6 3.8L 230ci - Pioneer# 602018 - Center Front Chrysler 1115744
L6 3.8L 230ci - Pioneer# 602014 - Upper Left/Right Chrysler 1269527

Engine Full Gasket Set (230) - Fel-Pro FS 7564 C-2 Full Gasket Set
Engine Gasket Set (230) - Fel-Pro HS 7564 C Cylinder Head Gasket Set
Engine Gasket Set (251) - Fel-Pro FS 7688 C-2 Full Gasket Set

Engine Head Gasket (230) (1117542, 1311806, 1326318, 1326319, 1401344, 1401345, 859224) - FEL-PRO 7564C
Engine Head Gasket (251) (1327338, 2205504, 312746117) - FEL-PRO 7688C

Manifold Gasket Set (230) (780460) FEL-PRO MS8009B
Manifold Gasket Set (251) (780462) FEL-PRO MS8583B

Valve (push rod) Cover Gasket (230) FEL-PRO VS4253C
Valve (push rod) Cover Gasket (251) FEL-PRO VS917C (cork) FEL-PRO VS917R {#780475, 980584} (rubber)

Oil Pan Gasket (230) FEL-PRO OS4250C
Oil Pan Gasket (251) FEL-PRO OS915C (1243678, 933439)

Rear Main Seal (230) (1942-1953 Up-To T137-25992) FEL-PRO BS6300 {#891458, 996378}
Rear Main Seal (230) (1954-1960 After T137-25992 Victor JV134-9)
Rear Main Seal (251) Victor JV134-9 (cannot locate this part)

Timing Cover Gasket (230) 1942-1946 JV-755, 1947-1953 JV-757
Timing Cover Gasket (230) 1954-1960 JV-826 Fel-Pro TCS 4155-2 Timing Cover Set
Timing Cover Gasket (251) JV-826 Fel-Pro TCS 4155-2 Timing Cover Set

Cylinder Head Gasket Installation Instructions
Permatex Copper Spray-A-Gasket


Universal Joints WC, WDX, PW, and M37

Intermediate Shaft - Moog 304 (3” Inside Lockup x 1.232” Brg. Cup) DODGE 5380 series
Front & Rear Propeller Shafts - Moog 305 (2” Inside Lockup x 1.231” Brg. Cup)

Winch Drive Shaft
Front & Rear U Joint
Up to Serial. No. 88759859) (WC & WDX) - Moog 853 (2.910" / 2.910"” Cap-to-Cap x .875” Brg. Cup) Requires machining .015+off outside end of bearing cross and .015+ off outside end of Brg. Cup, or silicone seal around the cup and .015+ shim under the lock plate cut for cup/bolt holes)

(After Serial. No. 88759859) - (PW & M37) - Neapco 1-0170


Seals



Oil Seal for the WDX - WM300 Power Wagon

National number codes
#47****non-reinforced with double lip
#45****reinforced with single lip
#41****reinforced with double lip
#******NPolyacrylate High Temperature material

Chrysler Description Parts List Code Dodge Part Number  
Axle Drive Pinion Bearing Oil Seal

Note: No modern cross reference exists for the original 2-piece seal. Numbers and sizes listed are dimensionally correct replacements for only the inner half of the seal assembly.

3-22-45 928 114
National Part Number Size Type
472041N1.875 I.D. x 2.506 O.D. x .375 Double lip, Poly
4720411.875 I.D. x 2.506 O.D. x .375 Double lip
4508321.875 I.D. x 2.506 O.D. x .500 Single lip, Reinforced
*CR #185651.875 I.D. x 2.506 O.D. x .313 Single lip
National Sleeve #99187 *CR Sleeve #99817 
Belt Pulley Drum Oil Seal 21-08-130 1189 732
National Part Number Size Type
410183N1.750 I.D. x 2.754 O.D. x .500 Double lip, Poly, Reinforced
4101831.750 I.D. x 2.754 O.D. x .500 Double lip, Reinforced
4721791.750 I.D. x 2.754 O.D. x .312 Double lip
*CR #175231.750 I.D. x 2.754 O.D. x .313 Single lip
National Sleeve #99174 *CR Sleeve #99175 
Belt Pulley Input Shaft Oil Seal 21-08-108 1189 726
National Part Number Size Type
410097N2.125 I.D. x 3.355 O.D. x .468 Double lip, Poly, Reinforced
4100972.125 I.D. x 3.355 O.D. x .468 Double lip, Reinforced
4134692.125 I.D. x 3.355 O.D. x .375 Double lip, Reinforced
*CR #213362.125 I.D. x 3.355 O.D. x .438 Single lip
National Sleeve #99210 *CR Sleeve #99210 or 99212 
Front Axle Drive Shaft Oil Seal 2-12-8 924 432
National Part Number Size Type
4104511.500 I.D. x 2.066 O.D. x .437 Double lip, Reinforced
*CR # 148641.500 I.D. x 2.066 O.D. x .313 Single lip
Mechanical Governor Input Shaft Oil Seal    
National Part Number Size Type
471442N.500 I.D. x 1.003 O.D. x .250 Double lip, Poly
471442.500 I.D. x 1.003 O.D. x .250 Double lip
*CR #4985.500 I.D. x 1.003 O.D. x .250 Double lip
Mechanical Governor Rocker Shaft Oil Seal    
National Part Number Size Type
50385S.375 I. D. x . 754 O. D. x .250 Single lip
330385.375 I. D. x . 754 O. D. x .250 Single lip
*CR #3680.375 I. D. x . 754 O. D. x .250 Double lip
Pillow Block Front Output Shaft Oil Seal 21-08-75 1189 686
National Part Number Size Type
4104631.375 I.D. x 2.754 O.D. x .500 Double lip, Reinforced
4704631.375 I.D. x 2.754 O.D. x .500 Double lip
*CR #139061.375 I.D. x 2.754 O.D. x .500 Single lip
National Sleeve #99139 *CR Sleeve #99138 
Pillow Block Companion Yoke Seal 21-08-75 1189 685
National Part Number Size Type
410286N1.625 I.D. x 2.754 O.D. x .500 Double lip, Reinforced
4702861.625 I.D. x 2.754 O.D. x .500 Double lip
4734431.625 I.D. x 2.754 O.D. x .375 Double lip
*CR #163681.625 I.D. x 2.754 O.D. x .313 Single lip
National Sleeve #99162 *CR Sleeve #99162 
PTO Output Shaft Oil Seal 21-08-25 1193 752
National Part Number Size Type
4102361.125 I.D. x 1.878 O.D. x .437 Double lip, Reinforced
4702361.125 I.D. x 1.878 O.D. x .437 Double lip
National Sleeve #99112 *CR Sleeve #99116 
PTO Shaft Center Bearing Oil Seal 21-08-32 556 939
National Part Number Size Type
4100941.937 I.D. x 3.194 O.D. x .437 Double lip, Reinforced
4700941.937 I.D. x 3.194 O.D. x .437 Double lip
4734621.937 I.D. x 3.194 O.D. x .375 Double lip
PTO Shifter Shaft Oil Seal 21-08-139 926 162
National Part Number Size Type
410895.750 I.D. x 1.379 O.D. x .312 Double lip, Reinforced
470895.750 I.D. x 1.379 O.D. x .312 Double lip
471554N.750 I.D. x 1.379 O.D. x .250 Double lip, Poly
*CR #7513.750 I.D. x 1.379 O.D. x .250 Double lip
National Sleeve #99076 *CR Sleeve #99076 
Rear Wheel Bearing Outer Oil Seal 22-07-14 915 496
National Part Number Size Type
60772.062 I.D. Flange Leather
*CR #207662.062 I.D. Flange Nitrile
National Sleeve #99205 *CR Sleeve #99205 
Timing Chain Case Cover Oil Seal 9-23-18 1088 602
National Part Number Size Type
4103452.187 I.D. x 3.194 O.D. x .437 Double lip, Reinforced
4703542.187 I.D. x 3.194 O.D. x .437 Double lip
61862.187 I.D. x 3.194 O.D. x .718 Double lip, Poly
*CR #219382.188 I.D. x 3.194 O.D. x .640 Double lip
National Sleeve #99218 *CR Sleeve #99218 
Transfer Case Companion Yoke Oil Seal 16-20-20 927 367
National Part Number Size Type
470308N2.125 I.D. x 3.066 O.D. x .500 Double lip, Poly
4103082.125 I.D. x 3.066 O.D. x .500 Double lip, Reinforced
*CR #212132.125 I.D. x 3.066 O.D. x .500 Double lip
National Sleeve #99212 *CR Sleeve #99212 
Transfer Case Shifter Shaft Oil Seal 21-109-10 915 561
National Part Number Size Type
410141.750 I.D. x 1.254 O.D. x .375 Double lip, Reinforced
470954N.750 I.D. x 1.254 O.D. x .250 Double lip, Poly
*CR #7443.750 I.D. x 1.254 O.D. x .250 Double lip
National Sleeve #99076 *CR Sleeve #99076 
Transmission Rear Bearing Oil Seal 21-22-2 593 596
National Part Number Size Type
4103082.125 I.D. x 3.066 O.D. x .500 Double lip, Reinforced
470308N2.125 I.D. x 3.066 O.D. x .500 Double lip, Poly
4703082.125 I.D. x 3.066 O.D. x .500 Double lip
7100212.125 I.D. x 3.068 O.D. x .370 Double lip, Poly, Reinforced
*CR #212132.125 I.D. x 3.066 O.D. x .500 Double lip
National Sleeve #99212 or 99210 *CR Sleeve # 99212 or 99210 
Wheel Bearing Inner Oil Seal 22-06-18 915 499
National Part Number Size Type
4174852.812 I.D. x 3.881 O.D. x .437 Double lip, Reinforced
550102.812 I.D. x 3.881 O.D. x .468 Leather
*CR #281162.813 I.D. x 3.881 O.D. x .438 Single lip
National Sleeve #99281 *CR Sleeve #99281 
Winch Gear Box Oil Seal 21-97-51 926 741
National Part Number Size Type
4102301.000 I.D. x 1.756 O.D. x .437 Double lip, Reinforced
470541N1.000 I.D. x 1.756 O.D. x .375 Double lip, Poly
411703N1.000 I.D. x 1.756 O.D. x .312 Double lip, Poly, Reinforced
*CR #99671.000 I.D. x 1.756 O.D. x .250 Double lip
National Sleeve #99100 *CR Sleeve #99100 



Aftermarket Parts


Instrument panel LED 12V replacement light bulbs

Home - Trucks for Sale - Forum - Search - Parts - About Us - Links - Privacy Policy
© 2018 dodgepowerwagon.com
Contact Us